No.
Clearview Mirrors will not fall off or blow back in the event of a road train passing you.
Should you experience any difficulties with your Clearview Mirrors at any time, our friendly technical staff are more than happy to assist in solving your problem.
Clearview Accessories takes great pride in our after-sale product service.
Yes.
Clearview Mirrors fold back against your vehicle door if hit. They also fold forward if brushed past in a vehicle park.
Installation guides are available on our YouTube channel, ‘Clearview Accessories.’ If you are unsure about installing your Clearview Product,
No.
Clearview Mirrors are designed to be vehicle specific. So they will not fit other model cars.
However, Clearview is always adding to their available vehicle model range.
If you have a vehicle that Clearview does not currently make their towing mirrors for, and you would like our mirrors on your vehicle – PLEASE LET US KNOW.
If the demand is there for a particular vehicle, we’ll add it to our product range – simple as that!
Yes!
It’s easy to remove Clearview Mirrors and refit your old mirrors at any time without any problems at all.
For a small charge, any mechanical workshop or auto electrician should be able to fit Clearview Mirrors for you.
Depending on the complexity of the installation, the fitting will vary from vehicle to vehicle. Any installation requiring any special fittings and/or hard wiring will require longer fitting times (eg. 360º Camera fitting/calibration, any electric hard-wiring kits, OAT sensors, and any other complex installations etc).
Original Clearview mirrors come in either a chrome or a textured black finish.
When purchasing Clearview Mirrors with indicators:
When purchasing Original Clearview Mirrors without indicators, either electric or manual:
If you already have that function in your vehicle, then the Powerfold will pick up this function when it is installed. However, if you don’t have that function in your vehicle, then the Powerfold won’t automatically fold in and out.
The auto folding capability is usually programmed into the vehicle itself.
The Powerfold mirrors can fold manually, however the manual fold mechanism is only designed as a safety feature. Through the lifespan of the product, manual folding will occur, such as people walking into them or accidentally bumping them. The internal mechanisms are designed to withstand this accidental manual folding during normal usage. It is not recommended for the mirrors to be manually folded constantly, as it will prematurely wear out the internal folding mechanisms and reduce the lifespan of the product.
If your vehicle already had powerfolding function in the original mirrors, then the Clearview Powerfold Mirrors will be a plug and play product and operated using your original controls.
If your vehicle didn’t have powerfolding function in the original mirrors, then you will need to purchase the suitable Powerfold wiring kit and have an auto electrician to conduct the work.
Some vehicles have no provision for Powerfold switch (either all provisions already used or no provision at all) may require cutting of the dash to fit switch in, or fascia panel for switch mounting may need to be purchased from other retailers.
After the mirrors are installed, they need to be cycled a few times. This will allow all the internal mechanisms to set and find the proper positions. If the mirror head is still loose/floppy after they’re cycled, please contact tech support.
In most vehicles, the mirror housings are angled differently between the driver and passenger side. This is because when you sit in the car, you are off center, so generally the passenger side mirrors are closer to the vehicle body to allow you to have the same field of vision in the mirror. So it is completely normal.
Generally the passenger mirror will fold/unfold quicker, as it is closer to the vehicle body and therefore travels a shorter distance compared to the driver side mirror. See previous question in regard to why the mirrors are angled differently.
Apart from the mirror head itself, everything else on the Powerfold is different.
When the Powerfold mirror is being cycled to find its original driving position, it will “jump” back into position and make an audible click sound when mechanisms realign. Once the mirror has found the original position and have been cycled, check for looseness and mirror movement. If they feel firm then the mirrors have not been damaged. If they still feel loose, please contact tech support.
Yes! Depending on the complexity of the installation, Clearview mirrors are extremely easy to install and mount to the vehicle’s original OEM mirror mounts. Depending on the vehicle’s current mirror options, Clearview mirrors include plug and play wiring looms. Instructional videos are also available on our website (clearviewaccessories.com.au) in the “HOW TO” section. Clearview recommends that any installation requiring hard wiring be done by a licensed auto electrician.
Yes, you can. But it comes at a greater expense than if you were to order the mirrors with indicators. Installation to the mirror head will require longer time and more parts to dismantle
Identifying based on model selection
The 360-Degree Camera is standard on Ranger Wildtrak, Platinum and Raptor only. Optional as part of a pack at additional cost on XLT 4×4 and Sport pick-up models. Not available on XL, XLS, XLT 4×2 or XLT Chassis Cab.
The 360-Degree Camera is standard on Everest Platinum only. Optional on Trend & Sport at additional cost. Not available on Ambiente.
Identifying based on a physical mirror check
A Next Gen Ford Ranger / Everest with 360 degree camera mirror includes:
• an OAT sensor (on the LHS mirror only)
• puddle light (in the middle)
• and camera (on the outside edge)
Identifying based on centre display options
When looking at the large centre display, if one of the available camera views is a bird’s eye top-down view, then it is a camera model.
Power Folding towing mirrors are motorised, allowing them to fold or unfold at the press of a button. Manual mirrors do not have a motor to fold or open the mirrors.
The EasySlide will elevate your fridge by 28mm.
The slide can be set back up to 150mm away from the outmost point of the canopy/tray/drawers. Although the back of the tray is 170mm away from the front edge of the slide base, we don’t recommend the set back distance to be greater than 150mm.
Step 1. Determine the overall height of the EasySlide you wish to install. ES100+ & ES150+ have overall height of 470mm, ES220+ have an overall height of 525mm.
Step 2. Mark out the overall height of EasySlide on the canopy profile, measure the corresponding horizontal distance to the out most point of your canopy. This distance is your minimum set back distance required*.
*There are a few factors that will affect this set back distance, such as
Step 3. Check the set back distance from “Step 2”, making sure it is below the maximum set back distance of 150mm.
Yes, the EasySlide can be fitted over Titan drawers. However, there are a few factors to consider when fitting the slide on Titan drawers, see below
– Titan drawers have a lower height than some other drawers on the market. The height measurements on the Titan drawers is between 240-270mm, depending on model. This may prevent the EasySlide to lower fully, as reported by some customers.
– The lashing rings/strap rings on top of titan drawers may need to be removed prior to fitting EasySlide. The rings protrude from the drawer top surface, when EasySlide is bolted over the top, it causes the slide to distort and affects the operation of the slide.
– The EasySlide should not be bolted over the aluminium trim found on the Titan drawers. This is because the aluminium trim is higher than the drawer top, and when slide is bolted over this trim, it causes the edge of the slide to roll inwards and reduces some of the clearance gaps within the slide. In most cases, this leads to slide components interfering with each other.
– Titan drawers usually have one fixed top platform and built-in sliding top platform. Many people have asked if the EasySlide can be mounted on top of the sliding platform to allow more extension. This can be done, but it is not usually recommended, as the load created from the operation of the EasySlide may damage the drawers.
This is a common questions for people who wish to mount the EasySlide directly into the boot of the vehicle without any drawers. The EasySlide was designed to lower fridges back to the boot floor height when mounted on top of drawers. It will not extend far enough to allow the fridge to be dropped beyond rear bumpers or tail gates.
In most cases, when the cog mechanism is not working as it should, it’s something with the way the handles are installed. Often when the handle has not been placed over the locating point properly, so the pawl and cog are misaligned (See image below).
Please ask customer to send images of the misaligned cog and image of the bolt securing the handle and forward onto tech support for assessment.
For the travel lock bearing to interfere with the base plate of the EasySlide, the distance between the two would have been reduced. This could happen due to the following:
1. If the front of the EasySlide is sitting on the trim of the drawers, then when it is bolted down, the front of the EasySlide will roll inwards, reducing the distance between the front lip and travel lock bearing. The slide will need to be moved off the trim or it will need to be packed up so when it is bolted, the rest of the slide is sitting at the same level as the trim.
2. If the fridge is strapped down too tightly on the EasySlide tray assembly, it will cause the tray to distort, where edge of the tray will roll upwards, creating a bow. The middle of the tray will usually dip down as a result, causing the travel lock bearing to sit lower than it should, leading to interference.
3. Some drawers have lashing rings or buckles on the top surface, if the EasySlide is mounted over these rings, it will cause the slide to distort, which could cause the interference issue.
Please request photos of the setup and forward to tech support if problem still persists.
This depends on the setback distance, however, should be approximately between 120mm and 145mm.
We recommend installation to be completed by professionals, as there is electrical wiring involved, as well as removal of vehicle trims. However, if the individual is hands on and have experience working on cars, then they’re most likely be capable of performing the installation themselves.
The motors are IP68 rated, meaning they are dust proof and safe for complete water immersion.
The boards are equipped with a safety cut-off feature, where if there are anything that prevents the boards from fully deploying, they will stop. To reset, open and close the door again. Some customers have installed a kill switch into the Power Board system for off roading, which disables the Power Boards completely until they’re required again.
AAccording to Mazda dealer, the BT-50 Extra Cab/Freestyle Cab/Space Cab only have provision for two Power Board brackets per side. Our BT-50 Power Boards requires three brackets per side, so it will not fit as intended.
So far, all the 78 Series Troopy we have seen have the exhaust system running down the passenger side of the vehicle. The space between the exhaust and cabin isn’t big enough to fit the Power Boards brackets. So Power Boards can’t be fitted.
No, we’ve included four new-look fridge straps to keep your fridge secure.
As standard, the Power Slide requires a 15-amp Anderson Plug Power Supply.
Yes! Our Power Slide XL is engineered to suit some of the biggest fridges on the market!
This includes the ARB 96L, DOMETIC & WAECO 95L, MYCOOLMAN 85L, 96L, 105L, EvaKool, Giant 80L, Kickass 95L, Kings 75L, Rydge Rider 72L.
There are four Power Slide models available,
This includes the PS-S, PS-M, PS-L and our largest size the PS-XL.
Yes! Instructional videos are also available in the “HOW TO” section of our website (clearviewaccessories.com.au).
The Unit Net Weight of the Clearview Power Slide XL is 38Kg.
Regular routine maintenance will also help to ensure continued smooth operation of your Clearview Power Slide®!
Please note that our Clearview Power Slide® is not designed for safe operation in an outdoor environment or to withstand the elements. Constant exposure to the elements such as rain and moisture can cause damage to the electrical components.
The Power Slide contains a load rating of 180kg, our lightweight Clearview Power Slide is designed to smoothly lower and raise a fully loaded fridge.
Simply unlock the travel lock mechanism, pull down on the yellow ergonomic slide quick-release runner levers and pull the fridge towards you to full extension.
Now the magic happens! Lower and raise your fridge with the press of a button for convenient access to its contents.
The Clearview Power Slide® is designed to be installed internally within a canopy, vehicle or trailer.
Please note that our Clearview Power Slide® is not designed for safe operation in an outdoor environment or to withstand the elements. Constant exposure to the elements such as rain and moisture can cause damage to the electrical components.
Depending on the complexity of the assembly, a dealer should be able to assemble the Power Slide™ in approximately 40 minutes to an hour. To assemble the Power Slide™ at home, this may take anywhere between 1 hour to 1.5 hours.
Yes. We have spare parts for all our products on our website. Our dealers also have a list of all our spare parts. If you cannot find the parts that you require, please contact us or any of our dealers to assist you with your inquiry
No. The Expanda slide is a straight fridge slide, it only slides out.
The Platform Area of the Large Clip-On Tray is 454mm (L) and 530mm (W)
The Platform Area of the Small Clip-On Tray is 454mm (L) and 390mm (W)
Rock Tamers® MudFlap System is an easy on and off way to protect your tow vehicle as well as whatever you are towing from hazardous rocks, mud, debris & road tar.
Rock Tamers® Mud Flaps protect your tow vehicle and towable by acting as a barrier and safely deflecting road debris away. When you’re on the move, an air whirl appears between your vehicle and your towable where road debris and particles get between the two. When the rear end of the tow vehicle is not protected, this debris can cause damage such as dents and chipped paint, to the vehicle. As your wheels rotate, rocks and debris get caught in the wheel tread which are then flung out, causing potential damage to the towable behind you.
Rock Tamers® are easily removable, and installation is quick and easy with no drilling required, making Rock Tamers® a convenient solution for when not towing full-time.
When travelling, the mud flaps need to be sitting at about 45 degrees to be effective. Adjusting the static angle will help achieve this. The static angle of the mud flaps can be increased up to 35 degrees from the vertical. This will enhance the performance of the mud flaps and help eliminate the chance of stones rebounding back onto the tow vehicle.
Clearview Accessories provides a free Rock Screen with every set of Rock Tamers. This lightweight mesh insert is also available to be purchased separately for vehicles regularly travelling on gravel roads and off road driving. This insert, when fitted between the two flaps, will reduce the occurrence of stray stones, debris etc. rebounding off the A-frame of your tow vehicle. (A loose-fitting mesh will last longer than a tight-fitting mesh)
The lowest point of the mud flaps need to hang a minimum of 100mm off the ground when hitched or fully loaded. The mud flap length may require cutting to fit your specific vehicle.
Rock Tamers must be removed prior to entering any drive through car wash
To extend the life of your Rock Tamers, when not in use, spray the hub and fittings with a lanolin-based spray and wipe off excess. This will protect against corrosion etc. particularly when used in salty conditions.
Can’t find your vehicle? Click here
3 Frog Court, Craigieburn VIC 3064
(03) 8351 9933Unit 1/49 Doherty Street, Brendale
QLD 4500, Australia
Copyright 2022 – Website by Net Search
